...

One-day Sandless Refinishing

For most flooring jobs in Denver, you don’t need a permit. Refinishing hardwood, installing new hardwood, LVP or laminate, and replacing carpet or tile in the same spot are all on the city’s no-permit list. A permit comes into play when the work goes below the surface: structural subfloor repairs, changing floor levels, or adding things like electric radiant heat.

We refinish and install floors across the Denver Metro Area every week, so we get this question a lot. Here is the plain-English version, with the city’s own pages behind it.

Jrhardwoodfloorrefinishingandcleaning
Refresh Your Floors With Expert Care
J.R. Hardwood refinishes and installs floors across the Denver Metro Area, with guidance tailored to each floor’s condition.

Explore floor services

TL;DR

Table of Contents

When you don’t need a permit in Denver

The City and County of Denver says on its residential interior remodel page that painting, papering, tiling, floor coverings, refinishing wood floors, countertops, carpeting and cabinets are exempt. In practice, that covers the jobs most homeowners call us about:

The common thread is “like for like.” You are changing the surface, not the structure, the plumbing or the wiring. Think of it as a glow-up for the floor you already have, or a wardrobe swap on top of the same frame.

Other Denver-area guidance says much the same. Jefferson County’s homeowner page is a reminder that neighboring jurisdictions publish their own lists, so if you live outside the city limits, check your own city or county rather than assuming Denver’s rules apply.

When a flooring project can trigger a permit

Here is where the “no permit” answer gets a little more nuanced. According to this Denver flooring cost guide, permits enter the picture when work touches the structure of the floor. Typical examples:

Situation Permit likely? Why
Refinishing existing hardwood No Surface finish only
New hardwood, LVP or laminate over the same subfloor No Floor covering replacement
Subfloor repair or replacement Often yes Touches structure
Raising or lowering floor levels Yes Structural change
Electric radiant heat under new flooring Yes, an electrical permit Separate electrical work
Moving walls, plumbing or wiring while you are at it Yes Not flooring work

That same guide reports subfloor permits typically run $75 to $250 and structural floor-level permits $200 to $500, with a 2 to 4 week lead time for the latter. Treat those as ballpark figures from a third party, not official city fees. For the city’s actual fee structure, check Denver’s own permit pages or a fee calculator before you budget.

The “hidden work” trap

Many homeowners figure that because the surface floor doesn’t need a permit, nothing else matters. That’s not quite right. The floor itself is simple. What sits under it, or around it, is what permits are designed to manage: fire ratings, structural soundness, electrical safety.

Surface flooring versus hidden work concerns

A good example is a renovation where the old floor comes up and you find a soft, damaged subfloor. Swapping a few boards is one thing. Replacing large sections can cross into structural territory. That is a good moment to pause and call the city before the new flooring goes down.

Older homes: the lead paint rule matters more than the permit

If your Denver home was built before 1978, the more important rule is usually not a Denver permit at all. It is the federal EPA Renovation, Repair and Painting (RRP) rule. A summary of the rule explains that renovation work in pre-1978 housing must be done by EPA-certified firms using certified renovators, and it names sanding among the activities that can create lead dust.

The Denver cost guide adds a practical threshold: a firm disturbing more than six square feet of painted surface, say by removing baseboards, needs to follow containment, HEPA dust control and cleaning-verification steps. It also warns that skipping this can cause insurance and fine problems. Details and penalty amounts are best confirmed directly with the EPA.

What does that mean for you?

  1. Ask your contractor when the house was built, or tell them up front.
  2. Ask whether they handle lead-safe work practices if baseboards or trim will be disturbed.
  3. Keep kids, pregnant family members and pets away from the work area, as your contractor directs.

If you have lead concerns for your family, talk with your doctor or your local public health department. We can tell you how our process works, but we are floor specialists, not health professionals.

Do you need a permit to put in hardwood floors?

Short answer: for a straightforward installation over an existing subfloor, no. A permit-exemption roundup puts flooring squarely in the almost-certainly-clear category, though it also notes that checking your city’s published list is free. We agree with that approach.

Where installs get more involved:

Who pulls the permit, and who can do the work?

If your project does need a permit, Denver has two main routes. A licensed contractor can apply, or you can apply as an owner. Per the city’s homeowner permit page, homeowner permits are for single-family homes. You must be the legal owner and resident. Permits can’t go to trusts, LLCs or corporations, and you can’t pull one for ADUs, townhomes, condos or duplexes, even for the unit you live in. The city also notes that general contractor homeowners can hire licensed subcontractors, who pull their own trade permits.

One correction worth making: you may see online that homeowners can only use this route once every five years. The city’s page applies that limit to building a new single-family home, not to renovations or additions.

Colorado has no statewide flooring contractor license, so hiring well comes down to checking the basics yourself:

Rules that have nothing to do with the city

A permit isn’t the only gatekeeper. Before you book, check:

These are rules we hear about from customers regularly, but they vary building by building, so your HOA documents are the final word.

Our perspective: why we call the city on anything unusual

We have refinished and installed floors long enough to know that 95 percent of flooring questions have a boring answer: no permit, just good prep and good craftsmanship. The other few percent are why we always ask a few questions before quoting.

Here is how we think about it.

Start with the floor, not the form. Most of our calls begin with photos. We look at the species, the existing finish, the wear and any signs of moisture or movement. Often we can tell right away whether it is a clean-and-recoat job or something deeper. We would rather steer you toward a refinish than a full replacement if your floor has life left in it.

Ask about the age of the house. For pre-1978 homes, the lead paint rules shape how we plan the job, particularly around trim.

Keep it simple when you can. City code officials themselves recommend checking with the local building division before you start, even when you think you are exempt. A five-minute call beats an inspector flagging something later.

Our perspective: why we call the city on anything unusual — overview diagram

Be honest about scope. If a job turns into subfloor repair, we say so before it happens, not after.

The owner personally answers inquiries and does the work, so the person who tells you what your floor needs is the person standing on it.

— J.R.

What it costs when no permit is needed

Since most flooring jobs skip the permit fee, your budget is mostly labor and materials. Our published rates per square foot:

Service Our price
Full sanding and refinishing $4.20 to $5.50 per sq. ft.
Wood floor cleaning from $1.50 per sq. ft.
Screen and recoat from $2.50 per sq. ft.
Wax removal from $2.50 per sq. ft.

Your final number depends on the floor’s condition, the finish and the layout. For a deeper breakdown, see our Denver price guide for refinishing per square foot.

Planning your project: a simple checklist

  1. Define the work. Surface only, or will anything structural change?
  2. Check the house age. Pre-1978 means lead-safe practices.
  3. Read your HOA or lease. Get approval in writing.
  4. Call the city if unsure. Describe the scope and ask if a permit applies.
  5. Get a written quote. Photos make this easy; we offer free quotes over the phone from your description and pictures.
  6. Choose your finish. If you have pets or a tight timeline, ask about our instant UV-curable finish, which allows same-day walk-on.
  7. Schedule. Tell us your move-in or listing date and we plan around it.

Ready to refresh your floors?

If your project is a refinish, recoat, clean or new installation, you can usually skip the permit paperwork and get to the good part. We serve Denver, Parker, Castle Rock, Boulder, Colorado Springs and surrounding communities. Browse our flooring services and published rates, then send us a few photos for a free quote. We will tell you honestly whether your floor needs a refinish, a lighter touch, or a closer look at the subfloor.

Planning a new floor? Our hardwood floor installation page for Denver walks through what to expect.

FAQ

Do you need a permit to refinish hardwood floors in Denver?

No. Denver’s residential remodel guidance lists refinishing wood floors among work that doesn’t need a permit. If you live in an HOA or condo, check their rules separately. In a pre-1978 home, ask about lead-safe practices.

Do you need a permit for a subfloor?

It depends on the scope. Minor repairs are often treated differently from replacing large sections, and structural changes typically need a permit. Call Denver’s Community Planning and Development office with your specific plan before you start.

What can a homeowner do without a permit in Denver?

Cosmetic work such as painting, papering, tiling, floor coverings, countertops and cabinet replacement is on the city’s exempt list. Work that changes structure, plumbing or electrical systems does not qualify.

Do you need a permit for a pergola in Denver?

Yes, pergolas are covered structures and Denver addresses them on its deck, porch and pergola page. Check the page for the current zoning and building requirements before you build.

Sources